Opel Astra A

1991-1998 of release

Repair and operation of the car



Opel Astra A
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Ventilation and heating
+ 5. Power supply system
+ 6. System of decrease in toxicity
+ 7. Coupling
+ 8. Transmissions
+ 9. Half shafts
- 10. Brake system
   10.1. Technical characteristics
   10.2. System of anti-blocking of brakes (ABS)
   10.3. Protivobuksovochny system
   10.4. Hydraulic system
   10.5. Hydraulic tubes and hoses
   10.6. Brake overlays of forward brakes
   10.7. Support of a forward brake
   10.8. Brake disk
   10.9. Protective guard of a forward disk brake
   10:10. Brake shoes of back brakes
   10:11. Brake drum of back brakes
   10:12. Wheel cylinder of a back brake
   10:13. Brake overlays of back brakes
   10:14. A support of a back brake (model with back disk brakes)
   10:15. Brake overlays of the emergency brake
   10:16. Guard of a back brake
   10:17. Brake pedal
   10:18. Vacuum amplifier
   10:19. Unilateral valve (servoamplifier)
   10:20. Main brake cylinder
   10:21. Emergency brake
   10:22. Lever of the emergency brake
   10:23. Ropes of the emergency brake
   10:24. The valve of restriction of pressure in a contour of back brakes
   10:25. Switch of fires of a stoplight
   10:26. Switch of alarm bulbs of the brake system
   10:27. ABS modulator
   10:28. ABS wheel sensor of a forward wheel
   10:29. Electronic control unit and ABS relay
   10:30. Case of a butterfly valve
   10:31. Vacuum diaphragm of a butterfly valve (antitowing system)
   10:32. Electronic control unit (antitowing system)
   10:33. Switch of antitowing system
+ 11. Suspension bracket and steering
+ 12. Body
+ 13. Electric equipment
+ 14. Electrical circuitries







10:14. A support of a back brake (model with back disk brakes)

GENERAL INFORMATION

Fixing bolts of a support of a back brake

Fixing bolts – are specified by shooters.

Removal

PERFORMANCE ORDER
1. Remove brake slips.
2. Hermetically close a mouth of a tank of brake fluid a polyethylene film.
3. Turn off a nut of connection of a brake tube on a support and disconnect a tube.
4. Turn off two fixing bolts and remove a support from the car.

Partition

PERFORMANCE ORDER
1. Clear a support, trying not to inhale dust.
2. Do not try to divide support halves.
3. Remove fixing clips of dustproof covers of pistons and remove covers.
4. Lower one of pistons deep into of a support by means of a clamp and compressed air squeeze out the second piston.
5. Close the open cylinder, remove a clamp and squeeze out the remained piston.
6. Remove consolidations from cylinders.
7. Examine the surface of pistons and cylinders on existence of scratches or wear tracks.
8. Clear pistons and cylinders brake fluid or methyl alcohol.
9. Grease with lubricant for brake cylinders pistons, cylinders and consolidations of pistons.
10. Install consolidations in flutes in cylinders.
11. Install dustproof covers on pistons, and accurately insert pistons into cylinders.
12. When pistons are partially inserted, install dustproof covers on rims in cylinders and establish fixing clips.
13. The lower bolts of fastening of a case of coupling to the block of cylinders.

Installation

PERFORMANCE ORDER
1. Installation is carried out upside-down removals.
2. Upon termination of installation pump over the corresponding contour of the brake system.